The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
The article in the next paragraphs relating to How to Install a Bathtub Yourself is especially entertaining. Don't bypass it.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can move speedily; if you have to open up a wall surface to remove the old tub and also place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will require a helper to vacate the old bathtub and set in the brand-new one. Make sure you have actually qualified yourself for the work and are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is better to take into consideration using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your shower room if you have currently bought a brand-new tub and also don't need to transform the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Preparing for the Setup
Firstly, the supporting structure supplied with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome because of the restricted accessibility that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bathtub in the called for position. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bath tub up until the level checks out degree.
To install taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also check all joints and brand-new pipework for leakages as well as tighten them if essential. Load the tub and also examine the overflow outlet and also the normal outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait up until the bathtub has been utilized at least when as this will settle it into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washers remain in area in between the faucet and the sink. Protect the tap in position with the supplier provided backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind should be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealer can split relatively very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is advisable to fit the tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very intrigued by Installing A Bathtub and I really hope you enjoyed the new entry. Feel free to take the time to share this blog entry if you liked it. Thanks for your time. Visit again soon.
Book A Service Call Report this page